Lennox-hearth EDV3530 series User Manual download pdf

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

LOG PLACEMENT GUIDE

LOG PLACEMENT GUIDE FOR LENNOX DIRECT VENT EDV3530, EDV4035

AND EDV4540 SERIES VENTED GAS FIREPLACE HEATERS

EDV3530, EDV4035 AND

EDV4540 SERIES

750,158M

REV. N/C 05/2003

GENERAL INFORMATION

This log placement guide has been prepared to present detailed log

placement illustrations and provide instruction to assist in the place-

ment of logs at the initial (new appliance) setup and after the annual

cleaning and inspection cycles. The information provided here is to

be used in conjunction with the Homeowner's Care and Operation In-

structions provided together with this document in the appliance lit-

erature packet. Please read the Homeowner's Care and Operation In-

structions completely before completing the procedures detailed in

this placement guide.

INITIAL INSTALLATION CONSIDERATIONS

If the logs are being installed for the first time, the following para-

graphs apply:

DO NOT attempt to install the logs until the appliance installation has

been completed, the gas line connected and tested for leaks and the

initial burner operation has been checked out.

Step 1. Remove the appliance front door.

Step 2. Remove the boxed log set from the interior of the firebox.

Remove the logs from their packaging. Handle logs carefully to pre-

vent breakage.

CERAMIC EMBER PANELS, LOGS AND GLOWING EMBER

PLACEMENT

Step 1. Install the Ceramic Ember Panels as shown in

Figure 3

. Panels

should be placed in the order shown.

A. Place the left and right panel against the corners as shown.

B. Align the two front legs of the grate assembly on the dimples and

align the two rear legs between the cut out as shown.

C. Place the front panel into its proper position as shown. Adjust the

panels to minimize the gaps.

Note: This appliance is provided with enough Glowing Embers for sev-

eral applications, do not feel compelled to use all that is in a new bag.

For best glowing effect, replace the ember material annually. Replace-

ment Glowing Embers are available (Catalog Number 88L53).

Step 2. Position the individual logs as shown in

Figures 4 and 5

. Logs

should be placed in the order shown. All logs that have notches to fit

over the grate tines should be positioned with these notches directly

against the grate.

Proper log placement is critical to encourage outstanding flame

appearance and prevent sooting. When positioned properly as

shown, logs will be positioned between flame peaks and will not

impinge any flames.

Step 3. Separate the Glowing Ember (Rockwool) into pieces about

the size of a quarter

Figure 1

. Keep the pieces fluffed up, not matted.

Distribute these pieces over the front surface of the burner, as shown

Figure 2

. Do not use more than is necessary. When properly posi-

tioned, the Glowing Embers will cover approximately 65% of the front

burner and with no appreciable gaps or openings. Ensure that the

main burner ports remain uncovered by the ember material.

Refer to

page 3 for EDV3530

Series appliances and to

page 4 for

EDV4035

EDV4540

Series appliances.

Figure 1

Figure 2

Glowing Embers

1 2 3 4

Summary of Contents

Page 1 - LOG PLACEMENT GUIDE

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.1LOG PLACEMENT GUIDELOG PLACEMENT GUIDE FOR LENNOX DIRECT VENT EDV3530, EDV4035AND EDV4540 SERIES VENT

Page 2 - CERAMIC EMBER PANEL PLACEMENT

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.2CERAMIC EMBER PANEL PLACEMENTFigure 3Catalog Number for the entire Ceramic Ember Panel set: 55M4601 (

Page 3 - EDV3530 LOG PLACEMENT

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.3EDV3530 LOG PLACEMENTFigure 4Catalog Number for the entire log set: 55M0201Log PartNumber Description

Page 4 - Figure 5

Comments to this Manuals

No comments

Lennox-hearth EDV3530 series User Manual

Browse online or download User Manual for Kiln Lennox-hearth EDV3530 series. Lennox Hearth EDV3530 series User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Kiln Lennox-hearth EDV3530 series