Lennox Hearth COUNTRY COLLECTION 506033-34 User Manual download pdf

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

BLOWER KITS

COUNTRY COLLECTION™ WOODSTOVES

P/N 506033-34

Rev. NC, 11/2009

HEARTH PRODUCTS

KITS AND ACCESSORIES

KIT CONTENTS

1 ea. Blower Assembly (item #1)

1 ea. Snap Switch and Control Panel Housings (item #2)

1 ea. Instruction Sheet

TOOLS NEEDED

5/32 Allen Wrench Or T Handle Wrench

9/16” Socket Wrench

9/16” Open End Wrench

Large Flat Head Screwdriver

FPO

INSTALLATION INSTRUCTIONS FOR INSTALLING BLOWER

KITS FOR USE WITH COUNTRY COLLECTION™ MODELS S160, SA160, SS210,

ST210, S260 AND ST310 FREESTANDING WOODSTOVES

WARNINGS

The blower must be plugged directly into a properly

grounded three-prong receptacle, 120 VAC, 60 Hz, single

phase. Do not cut or remove the grounding prong from

this plug. Do not route power cord under or in front of

appliance.

Installation must be in accordance with National Elec-

trical Code, ANSI/NFPA 70 - latest edition. In Canada,

the current CSA C22-1 Canadian Electrical Code - latest

edition.

DANGER: Disconnect power before servicing blower.

In the event that you remove the blower for any reason,

make sure a cover plate (available from Lennox Hearth

Products) is installed before using the heater. Excessive

rear wall temperatures will result if the stove is burned

without the cover plate. The cover plate is not necessary

if a blower has never been installed because a knock-out

will be in place to act as the cover.

THERMALLY ACTIVATED BLOWER KIT

Cat. No. Model Description

H7917

BLWR-FSB700-SS Blower Kit, FS Woodstoves

Figure 1 - Kit Contents

GENERAL INFORMATION

This optional blower kit can be installed to improve hot air distribution

throughout the room.

The 700-CFM room air circulation blower kit comes

with a variable speed control (rheostat) and an snap switch which will

provide automatic thermal activation of the blower, when desired (see

Blower Operation on Page 6).

If you encounter any problems, need clariﬁcation of these instructions or

are not qualiﬁed to properly install this kit, contact your local distributor

or dealer.

Read this instruction sheet in its entirety before beginning the installa-

tion.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

SHUT DOWN THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE

PROCEEDING.

1 2 3 4 5 6

Summary of Contents

Page 1 - WARNINGS

1NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.BLOWER KITSCOUNTRY COLLECTION™ WOODSTOVESP/N 506033-34 Rev. NC, 11/2009HEARTH PRODUCTSKITS AND AC

Page 2

2NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Figure 2WOODSTOVES WITH PEDESTAL BASELeg based units, see instructions on Page 4.Step 1. From re

Page 3

3NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.Step 5. With the snap switch bracket in place, using a 9/16” wrench or socket wrench you can now

Page 4 - Figure 13

4WOODSTOVES WITH LEG BASEStep 1. Using a 9/16” wrench or socket loosen the left heat shield bolt. This bolt is located on the bottom side of the leg

Page 5 - Figure 21

5Step 7. Plug the power cord into grounded 120 VAC receptacle. Do not route the power cord under the stove or allow it to come in contact wi

Page 6 - Figure 23 - Blower Controls

Comments to this Manuals

No comments

Lennox Hearth COUNTRY COLLECTION 506033-34 User Manual

Browse online or download User Manual for Pellet stove Lennox Hearth COUNTRY COLLECTION 506033-34. Lennox Hearth COUNTRY COLLECTION 506033-34 User's Manual

Summary of Contents

Comments to this Manuals