Lennox Hearth 999995 User Manual

ROTARY TILLEROPERATOR MANUALPart No 999995 www.kingkutter.com2150Eastern Ave.Gallipolis, Ohio 45631

Figure DFigure FFigure H10Figure EFigure GFigure I

SAFETY TRAININGz Safety is a primary concern in the design and manufacturing of our prod-uct. Unfortunately, our efforts to provide safe equipment ca

PREPARATIONz Never operate the tractor and tiller until you have read and completely understand this manual,the Tractor Operator’s Manual, and each of

13OPERATIONAL SAFETYz The use of this equipment is subject to certain hazards that cannot beprotected against by the mechanical means or product desig

14OPERATIONAL SAFETY continued...z Never allow the tilling tines to contact such items. Never assume an areais clear. Always Check!z Always stop th

OPERATIONAL SAFETY continued...z Pass rotary tiller diagonally through sharp dips and avoid sharp drops toprevent “hanging up” tractor and rotary till

ATTACHING TO TRACTORWARNINGNever stand betweentractor and rotary tillerwhile backing up tractorto the hitch.STEP 1Attach to tractor's category 1

ATTACHING TO TRACTOR continued...STEP 6Raise rotary tiller and remove blocking. Raise and lower rotary tiller inorder to locate the longest distance

18STEP 1Cutting the PTO shaft to length.NOTE: Be sure to cut equallengths of each PTO shaft section.Clamp end of PTO shaft in a viceand cut off shiel

OPERATING INSTRUCTIONSSTEP 1Before each use perform the maintenance described in maintenance section(page 20).STEP2Read, understand, and follow the in

2

NOTE: Do not allow the tractor engine or rotary tiller to bog down or stall. Thiscauses undue wear and tear on the tiller and tractor. If this cont

z Be sure electrical outlets and tools are properly groundedz Use adequate light for the job at hand.z Make sure there is plenty ventilation. Never o

22Top ViewSAFETY SIGN LOCATIONSThe types of safety signs and locations on the equipment are shown in theillustration below. Good safety requires that

231

2423

4525

67267

27Notes:

28TILLER: EXPLODED VIEW

29Ref. Part Name Part NumberTG-48 TG-60 TG-721 Lift Arm Brace 38010823679

3TO THE PURCHASERThis manual contains valuable information about yournew King Kutter II Rotary Tiller. It has been carefully pre-pared to give you hel

Ref.No.Part Name147122134Roll PinMale Tube End YokeFemale Tube End Yoke151045151050Tractor End YokeInner Tube 14 SeriesOutter Tube 14 SeriesCross Kit

Ref.No.Part Name 1840701 Hub Housing902341239023429020194505017CapSelf Aligning Ball Bearing (1310)Seal Double Lip(Pkg-2)3156789Bolt M-12-2590201190

32TG SERIES SIDE GEARBOX 184069

33Ref. Part Name Part Number1 Retaining Ring 90mm 90200523579141516181920Reta

34TG SERIES TOP GEARBOX ASSEMBLY

35Ref. Part Name Part Number1 Retaining Ring 72mm 9023012357912131415161718Retaining Ring 40mmHousing RTA-50Sq. Hd. Plug 1/4"-18 NPTBolt M-10-30

1. Limited Warranty.King Kutter II, Inc. (“King Kutter II”), 2150 Eastern Ave. Gallipolis, Ohio 45631, warrants to the original retail purchaser(“Purc

4It is the purchaser and/or operator’s responsibility to….zzzzz Read and understand the information contained inthis manual.zzzzz Operate, lubricate,

5CONTENTSITEM PAGESafety ...6Assembly Instructions ...

6SIGNAL WORDS:The signal words DANGER, WARNING and CAUTION are used withthe safety messages in this manual and with each safety sign. Theyare defined

7EQUIPMENT SAFETY GUIDELINESz Safety of the operator and bystanders is one of the main concerns in designing anddeveloping a tiller. However, every y

8ROTARY TILLER ASSEMBLY INSTRUCTIONSSTEP 1With rotary tiller still in crate, lay flat on a level surface. Cut banding straps on the two (2) upright cr

9STEP 4 Replace and tighten the 1/2” pipe plug and clean away any excess oil.See Figure C.STEP 5 Remove 1/2” Pipe Plug (Located at top of side gearbox